Processor Modules

The heart of ADwin Pro II

The processor module is the headquarters of the T11 ADwin-II Pro system. It leads into the ADbasic of programmed commands and accesses the inputs and outputs, and interfaces of the other modules. The processor module per-CPU-T11 offers the highest real-time computing power and is largely software-compatible with previous versions.

The following processor modules are available:

• ADSP TS101 (300 MHz)
• 256 MB DRAM, 768 MB RAM CPU
• Trigger Input
• 2 digital I / Os
• Ethernet interface 100 Mbit / s for PC communication, effective data throughput of 10 MB / s
• Boot Loader option for stand-alone operation

Multi-I/O-Module

All-rounder with A / D, D / O, counters, EtherCAT and SSI

The Multi-I/O-Modul MIO-4 for ADwin Pro II is the self-sufficient all-rounder for all signal types: it combines the responsive TiCo processor with analog and digital inputs and outputs. Thus, the intelligent plug-in card independently respond to readings and events, and free the CPU, for example, as a fast controller, digital filter for analog signals, function generator and intelligent supervision limit. For a wider range expansion Mio4-ET1 with counters, SSI decoder and EtherCAT interface .

• General
  • TiCo processor
  • 128 MB internal memory
  • 4 MB external SRAM
  • 37-pin D-sub connector
• Analog Inputs
  • 8 differential channels or 16 channels single-ended
  • ADC resolution 18 bits, conversion time of 2 microseconds
  • Multiplexer settling time 5 microseconds
• Analog Outputs
  • 4 channels
  • 16 bit resolution
  • 9 microseconds settling time
• Digital Inputs
  • 8 channels with TTL logic
  • in groups of 4 configurable as input or output
• Extension MIO-4-ET1 (Order) provides additional
  • 4 transistor outputs
  • 4 optically isolated inputs
  • 1 meter block with two 32-bit counters: An up-down counter and a counter to the period and duty cycle
  • 1 SSI-decoder
  • 1 EtherCAT interface (slave)

Analog Input / Output Modules

Interfaces for analog signals

The analog input and output modules for ADwin-Pro II , the interfaces with your instruments, analog transmitters, amplifiers and actuators. They are ideal for the rapid solution of time-critical and real-time tasks. The processor module per-CPU-T11 uses the ADwin-Pro II bus with up to 200 MB / s on the modules.

Analog Input Modules

• Inputs with Multiplexer
  • 8 / 16 channel differential or 32 single-ended channels
  • ADC resolution 18 bits, conversion time of 2 microseconds
  • Multiplexer-time 2 microseconds
  • optional TiCo
• Parallel analog inputs
  • one ADC per channel for synchronous data acquisition
  • 4 or 8 differential channels
  • Resolution 14, 16 or 18 bits
    • 14 bits: 0025 microseconds conversion time
    • 16 bit: conversion time 0.25 microseconds
    • 18-bit: 2.0 microseconds conversion time
  • 256 MB memory modules
  • 16-bit module: Optional averaging of a defined number of measurements.

Analog Output Modules

The analog output modules allow for synchronous data output to 4 or 8 channels without time delay. The DAC has a resolution of 16 bits and provide a wide bandwidth.

• AOut-4/16 Pro II, Pro II AOut-8/16
  • 4 or 8 channels
  • 16 bit resolution
  • 3 microsecond settling time
  • Data output up to 10 times faster than Pro I modules

Digital input / output modules

ADwin-Pro and digital signals

Digital input and output modules are the interfaces to your digital gauges and transmitters. Select the digital modules to suit your type of signal.

Digital output modules

• DIO-32, DIO-32-TiCo: 32 TTL inputs / outputs, automatic edge detection with a time stamp on the inputs, with optional TiCo and 256 MB memory
• OPT-16: 16 min optocoupler inputs. 100 ns switching time, automatic edge detection with a time stamp, adjustable per channel at 5 V, 12 V or 24 V
• REL-16: 16 relay outputs and 30 V as a closer, 4 ms response time, optionally available as an opener
• TRA-16: 16 transistor outputs, switching voltage 5 ... 30 V, switching time of 2.5 microseconds, optionally switch to ground
• PWM-16 (-I): 16 PWM outputs, TTL, either transistor switching outputs 5 ... 30 V, waveform adjustable per channel, 100 MHz reference clock, switching time 20 ns (TTL) or <3 microseconds (transistor)
• Custom input / output modules

Counter modules

Counter modules for high speed digital signals

The ADwin Pro -counter modules can be, for example, for connection of incremental encoders, the event count or pulse width modulation.

• Universal counter module, individually configurable 32-bit counter for the modes
  • Pulse counter
  • PWM analysis, period measurement
  • Incremental input clock / direction or A / B with 4-edge evaluation
  • 2 SSI inputs, 5 V differential (RS-422)
• Various inputs
  • Pro II-Cnt-T: TTL
  • Pro II-Cnt-D: 5 V differential (RS-422)
  • Pro-II-I Cnt: isolated 5 V / 12 V / 24 V
• Programmable TiCo processor, for example, for preliminary evaluation of complex counter signals

Bus Modules

Communication on all sides

ADwin Pro modules work with a variety of bus and serial interfaces. A ADwin Pro -system can simultaneously send messages and data via RS232 control via CAN-Bus devices and control a test.

The following interfaces are available:

• Pro-RSx II-2: 2 x RS-232 / RS-485 software-configurable, with TiCo
• Pro-RSx II-4: 4 x RS-232 / RS-485 software-configurable, with TiCo
• Pro-CAN II-2: 2 x CAN bus, Low-Speed ??or High-Speed ??(CAN 2.0 Part A + B, ISO 11898), triggering a CPU through a CAN message event possible; module is TiCo equipped.
• Pro II-LIN-2: 2 x LIN bus
• Pro II-LIN-4: 4 x LIN bus
• Pro-II pro-SL: 1 x Profibus slave interface
• Pro-Flex II-2: 2 x FlexRay, each controller has two channels available
• Pro II SL-EtherCAT: EtherCAT with 1 x slave interface
• Other fieldbus interfaces on request

Temperature Modules

Active sensing with ADwin-Pro II

Module for Pt-sensors

The temperature module-RTD-8 Pro II converts signals from Pt temperature sensors with analog-digital converters (ADC), allowing the query either the temperature or the applied voltage.

All necessary settings can be configured by software. On the module performs a sequence control data acquisition, which relieves the main processor of the Pro II system greatly. The module can also automatically signals a defined (interference) frequency signals from the digital filter.

Features:

• Suitable for temperature sensors Pt100, Pt500, Pt1000, Ni 100
• Measuring range depending on probe -200 ° C - +700 ° C
• Input filter 25 kHz
• Measurement resolution 0.015 ° C
• Accuracy ± 0.1 ° C

Module for thermocouples

The temperature module TC-II Pro-8-ISO converts signals from standard thermocouples and used to check the temperature or the applied voltage (with and without cold junction compensation).

All necessary settings can be configured by software. On the module performs a sequence control data acquisition, which relieves the main processor of the Pro II system greatly.

Features:

• Suitable for thermocouple type B, E, J, K, N, R, S and T
• Measuring range depending on the probe according to standard IEC 584-1
• Measurement resolution 0.1 ° C